CAXA数控车编程需要手工修改吗？

sunyi0011 · 发表于 2013-10-20 19:22:01

以下是CAXA数控车自动编程，但对刀效果不太好，请各位高手看看程序是否有问题并指教，谢谢！
O1234
N12 T0101
N18 G00 X102.795 Z74.091
N20 G00 Z69.300
N22 G00 X72.185
N26 G98 G01 X62.185 F5.000
N28 G01 X60.770 Z68.593
N30 G01 Z-113.407 F280.000
N32 G01 X62.185 Z-112.700 F20.000
N34 G01 X72.185
N40 G01 X58.185 F5.000
N42 G01 X56.770 Z68.593
N44 G01 Z36.593 F280.000
N46 G01 X60.370
N48 G01 Z-113.407
N50 G01 X61.785 Z-112.700 F20.000
N52 G01 X71.785
N54 G00 G40 Z69.300
N58 G01 X54.185 F5.000
N60 G01 X52.770 Z68.593
N62 G01 Z36.593 F280.000
N64 G01 X56.770
N66 G01 X55.356 Z37.300 F20.000
N68 G01 X65.356
N70 G00 G40 Z69.300
N74 G01 X50.185 F5.000
N76 G01 X48.770 Z68.593
N78 G01 Z36.593 F280.000
N80 G01 X52.770
N82 G01 X51.356 Z37.300 F20.000
N84 G01 X61.356
N86 G00 G40 Z69.300
N90 G01 X46.185 F5.000
N92 G01 X44.770 Z68.593
N94 G01 Z36.593 F280.000
N96 G01 X48.770
N98 G01 X47.356 Z37.300 F20.000
N100 G01 X57.356
N102 G00 G40 Z69.300
N106 G01 X42.185 F5.000
N108 G01 X40.770 Z68.593
N110 G01 Z36.593 F280.000
N112 G01 X44.770
N114 G01 X43.356 Z37.300 F20.000
N116 G01 X53.356
N118 G00 G40 Z69.300
N122 G01 X38.185 F5.000
N124 G01 X36.770 Z68.593
N126 G01 Z36.593 F280.000
N128 G01 X40.770
N130 G01 X39.356 Z37.300 F20.000
N132 G01 X49.356
N134 G00 G40 Z69.300
N138 G01 X34.185 F5.000
N140 G01 X32.770 Z68.593
N142 G01 Z36.593 F280.000
N144 G01 X36.770
N146 G01 X35.356 Z37.300 F20.000
N148 G01 X45.356
N150 G00 G40 Z69.300
N154 G01 X30.185 F5.000
N156 G01 X28.770 Z68.593
N158 G01 Z36.593 F280.000
N160 G01 X32.770
N162 G01 X31.356 Z37.300 F20.000
N164 G01 X41.356
N166 G00 G40 Z69.300
N170 G01 X26.185 F5.000
N172 G01 X24.770 Z68.593
N174 G01 Z36.593 F280.000
N176 G01 X28.770
N178 G01 X27.356 Z37.300 F20.000
N180 G01 X37.356
N182 G00 G40 Z69.300
N186 G01 X22.185 F5.000
N188 G01 X20.770 Z68.593
N190 G01 Z36.593 F280.000
N192 G01 X24.770
N194 G01 X23.356 Z37.300 F20.000
N196 G01 X33.356
N198 G00 G40 Z69.300
N202 G01 X18.185 F5.000
N204 G01 X16.770 Z68.593
N206 G01 Z66.593 F280.000
N208 G01 X20.370
N210 G01 Z36.593
N212 G01 X20.770
N214 G01 X19.356 Z37.300 F20.000
N216 G01 X29.356
N218 G00 G40 Z69.300
N222 G01 X14.185 F5.000
N224 G01 X12.770 Z68.593
N226 G01 Z66.593 F280.000
N228 G01 X16.770
N230 G01 X15.356 Z67.300 F20.000
N232 G01 X25.356
N234 G00 G40 Z69.300
N238 G01 X10.185 F5.000
N240 G01 X8.770 Z68.593
N242 G01 Z66.593 F280.000
N244 G01 X12.770
N246 G01 X11.356 Z67.300 F20.000
N248 G01 X21.356
N250 G00 G40 Z69.300
N254 G01 X6.185 F5.000
N256 G01 X4.770 Z68.593
N258 G01 Z66.593 F280.000
N260 G01 X8.770
N262 G01 X7.356 Z67.300 F20.000
N264 G01 X17.356
N266 G00 G40 Z69.300
N270 G01 X2.185 F5.000
N272 G01 X0.770 Z68.593
N274 G01 Z66.593 F280.000
N276 G01 X4.770
N278 G01 X3.356 Z67.300 F20.000
N280 G01 X13.356
N282 G01 X-1.044 F5.000
N284 G01 X0.370 Z66.593
N286 G01 X0.770 F280.000
N288 G01 X-0.644 Z67.300 F20.000
N290 G01 X72.185
N292 G00 G40 X102.795
N294 G00 Z74.091
N296 M09
N298 M30
%

sunyi0011 · 发表于 2013-10-20 19:32:57

请各位指教，不胜感谢！

显示全部楼层 · 发表于 2013-10-21 19:47:13

提示: 作者被禁止或删除内容自动屏蔽

sunyi0011 · 发表于 2013-10-24 12:56:04

楼上的同学能否具体指点？

djb2010 · 发表于 2013-10-29 13:40:18

没开主轴

sunyds · 发表于 2013-11-21 12:54:02

既没有开主轴，也没有指定主轴速度！

mengfanshen · 发表于 2013-12-12 16:55:57

我一般都是软件及手工，程序也简单，

sunyi0011 · 发表于 2014-1-6 15:31:30

主轴转速可以另外加进去，可是实际对刀怎么也对不准啊

15887936668 · 发表于 2019-9-12 21:35:07

N12 T0101这段后面加入
N14 G97 S800 M03

		自动登录	找回密码
密码			立即注册

wangzhanqiang2 该用户已被删除	发表于 2013-10-21 19:47:13 \| 显示全部楼层提示: 作者被禁止或删除内容自动屏蔽
wangzhanqiang2 该用户已被删除
	回复支持反对使用道具举报